I have been satisfied with this playpen so far. It has a nice size for my baby to play in. Most of her small to medium sized toys, plus a fold up sponge sofa(where she takes her naps during daytime when being unfolded), can all fit in there. And there is still room for me , even for my hubby to squeeze in and interact with her. It helps me a lot during daytime specially with two dogs running around in the house all day long. At least I don't have to worry about my baby girl getting knocked over and hurt by the dogs. I wish I had fund this product when I had my first two kids nine years ago.
The pieces were super easy to assemble. Just slide the rods on one piece into the holes on the next piece to connect them. I was a little disappointed that the rods/holes were not hexagonal like the instructions state. That would have locked them into position either straight or at an angle. Instead, the rods/holes are round, so the panels move around (accordion style) and won't stay in a straight line. There are suction cups on the bottom of the panels that might help if you're using it on a hard floor or smooth mat, but they're useless on carpet or textured mat.
I have been satisfied with this playpen so far. It has a nice size for my baby to play in. Most of her small to medium sized toys, plus a fold up sponge sofa(where she takes her naps during daytime when being unfolded), can all fit in there. And there is still room for me , even for my hubby to squeeze in and interact with her. It helps me a lot during daytime specially with two dogs running around in the house all day long. At least I don't have to worry about my baby girl getting knocked over and hurt by the dogs. I wish I had fund this product when I had my first two kids nine years ago.
The Lotus Travel Crib and Portable Baby Playard is a highly portable and lightweight playpen at just 11 pounds. This playpen is so easy to set up—it takes just 15 seconds! Breakdown is somewhat more difficult, but see the video below for instructions. The Lotus folds up into a backpack, which you can transport easily on all your family adventures. The sides of the playpen are made from soft, see-through mesh so you can watch baby play; the side even has a fun door that zips and unzips so baby can crawl in and out while supervised. More than just a playpen, the Lotus comes with a soft mattress, making it a safe and comfy place for baby to nap. Some consumers do not like that the mattress rests directly on the ground. Additionally, you will need to buy the Guava Family quilted sheets, because the mattress is not a standard size. This playpen is more expensive than average, at $198.
If a quick DIY play yard better suits your requirement then make one at home with an inflatable plastic kiddy pool. In case you have a kid’s plastic pool lying around in your house, then you can inflate it and convert into a play yard. Simply inflate the plastic frame, place a soft blanket or mattress inside it, and you just made a safe and comfortable place for your baby to play. Just make sure the walls of the pool are high enough to prevent your baby from crawling out. Also keep all sharp and pointy things away from the pool.
If you expect to frequently move your play yard from room to room, check its dimensions before you buy. Many interior doorways are only 30 inches wide—no problem for the 28-inch width of most basic models. But many deluxe models are wider—the Graco mentioned above, for example, would be a tight squeeze at 28.8 inches wide. Just be aware that you might find yourself folding a deluxe model to move it around inside the house.
MomJunction provides generic information on health for educational purposes only. It is not a substitute for professional health services, and cannot be used as a replacement for personalized health consultation. If you or your child has any health concerns, you should consult a healthcare professional. Please read our Disclaimer before proceeding to use our website.
Nice to keep baby out of trouble at home. Once he became mobile we had to do an "upgrade" as we noticed he was starting to hit his head on the X shaped metal bars. We tried some alternatives but the best so far was wrapping the metal bars with pool noodles (see picture). You'll need 8 pool noodles and some cuts (buy some extra in case you mess up). Use 2/3 of a pool noodle to wrap the internal bars and the remaining 1/3 to wrap half of the external bar. The pieces will also need a longitudinal cut along the length to fit the bar in. You'll also need some small cuts in the middle of the longer piece to fit the center rivet, where the mesh is attached to the bars. We got the pool noodles at the dollar store nearby for less than $10 and since ... full review
×